Primo Microphone Capsules
A tiny (6 mm dia) high quality Primo EM258 capsule as complete working microphone module ready to build in to a housing or enclosure. No soldering required Requires capsule and cable to be supported 1.0 metre screened cable. 3.5 mm stereo plug, the signal is sent equally to both the left and right channels. Primo EM258 Data Sheet EM172 Mono is available.
Omni directional (non-directional) Signal to Noise ratio 80dB (Self Noise 14dBA) Available as single capsules, 2 matched or 4 matched Also available with short wires pre-soldered Sensitivity -28 dB (+/- 3dB at 1kHz, 0dB=1V/Pa) Operating Voltage 3 V (2-10 V) Maximum input Sound Pressure Level 119 dB Diameter 10 mm, depth 4.5 mm, Weight 0.9 grammes. Primo...
Primo EM184 Cardioid Microphone Capsule. Available singly or as sensitivity matched pairs for stereo use. Available as 4 matched capsules for ambisonic use. Also available with pre-soldered wires
A tiny high quality capsule only 6mm in diameter and 2mm deep. Primo suggest the EM258 as a replacement for the Panasonic WM-61A. Signal to Noise ratio 74dB (Self Noise 20dBA) Sensitivity -32 dB (+/- 3dB at 1kHz, 0dB=1V/Pa) Operating Voltage 3 V (1.5-10 V) Useful Ultrasonic response
High sensitivity Electret Condenser Microphone. Omni directional Ultra low noise, Wide dynamic range (108db), High quality. 10 mm diameter. 3 wire connection Primo EM173 Data sheet
Ultra low noise | High Sensitivity Wide Dynamic range | Omni Directional Primo EM184 with wires are available. Superb quality electret condenser mic capsule, its extraordinarily low noise and high sensitivity makes this ideal for recording nature sounds, backgrounds and ambiences. PRIMO EM172 DATASHEET
A complete working stereo microphone module ready to build in to a housing or enclosure. Complete working microphone ready to plug in No soldering required Ideal for binaral use Does require capsule and cable to be supported 1.5 metre screened cable Metal bodied, gold plated, stereo plug Single version of this module is available here
Omni directional electret mic capsule. High performance, Low noise, High quality. Sensitivity: -42.0 (0dB=1V/PA) S/N Ratio: 70 dB at 1KHz Available as matched pairs This capsule requires a FET and circuitry. Primo EM23 Data sheet
Suitable for FC033 Primo EM258N 6 mm Omni Electret Capsule Made by Primo
Rubber Holder for 10 mm capsules Made by Primo in Japan Suitable for EM172, EM173, EM184 capsules Include in FC081 and FC084.
PVC Sleeve Holder for 10 mm microphone capsule, suitable for EM172, EM173 and EM184 capsules Internal diameter 9.5 mm External diameter 12 mm Height 8 mm Opening diameter 8 mm Capsule sits recessed from the front by approximately 1 mm
A PVC grommet with a 9.6 mm hole giving a good secure fit for 10 mm capsules including Primo EM172, EM173, EM184 External diameter 16 mm Panel hole size 13 mm Panel thickness 1.3 mm
A collection of parts to make a simple high quality stereo microphone 2 x Primo EM172 capsules 1 x Neutrik gold plated stereo 3.5 mm plug Cable length 1.5, 3 or 10 metres Heatshrink to cover exposed wire Basic wiring diagram Alternately our Module Primo EM172 module is available.
Spare metal clip for Clippy microphones, tough metal alligator clip with a sprung plastic holder to accept the microphone.
A beautiful aluminium enclosure for 10 mm capsules like the Primo EM172, 173 and 184. The top cover screws onto the body and has a metal grill for protecting the capsule. There are slots below the capsule making it suitable for cardiod use.
A foam windshield for our Clippy microphones The windshield is slightly hollow with a tighter neck so it stretches over the microphone and stays firmly in place It also covers the side slots on the mic For better wind protection see our small and medium 10 mm windshields here
Only one size is available. Alternative for Large windshiled. Microphone Windshield for 10 mm capsules, to help reduce wind noise. High quality foam, offer better protection for Clippy Mics Suitable for Primo EM172, EM173, EM184. Suitable for Clippy EM172 Microphone and Clippy XLR EM172 Microphone.
6mm Microphone Capsule Holder. A convenient means of mounting tiny capsules, the rubber also provides some vibration isolation. Internal diameter 6mm External diameter 10 mm Height 10mm Maximum width 17mm Suitable for Primo EM258 and other 6mm capsules.